SGI Techpubs Library

The new home for SGI documentation is the SGI Customer Portal, This site will be redirected to the new location later this month.

Hardware  »  Books  »  End-User  »  
SGI Origin 300 User's Guide
(document number: 007-4365-002 / published: 2002-06-11)    table of contents  |  additional info  |  download
find in page

SGI Origin® 300 User's Guide

Document Number: 007-4365-002


Written by Olivier Clarinval

Revised by Nancy Heller

Illustrated by Dan Young

Production by Karen Jacobson

Contributions by James Oliver, Ron Naminski, William Menezes, Charles Skandalis, David Alexander, Vince Duperron, German Rico, Hao Pham, Matt Law, Cherry Nuque, Lyle Stoll, Samuel West, John Kelly, Jim Passint, Keith Schilling, David Diederichs.

Cover Design by Sarah Bolles, Sarah Bolles Design, and Dany Galgani, SGI Technical Publications


© 2002 Silicon Graphics, Inc. All rights reserved; provided portions may be copyright in third parties, as indicated elsewhere herein. No permission is granted to copy, distribute, or create derivative works from the contents of this electronic documentation in any manner, in whole or in part, without the prior written permission of Silicon Graphics, Inc.


The electronic (software) version of this document was developed at private expense; if acquired under an agreement with the USA government or any contractor thereto, it is acquired as “commercial computer software” subject to the provisions of its applicable license agreement, as specified in (a) 48 CFR 12.212 of the FAR; or, if acquired for Department of Defense units, (b) 48 CFR 227-7202 of the DoD FAR Supplement; or sections succeeding thereto. Contractor/manufacturer is Silicon Graphics, Inc., 1600 Amphitheatre Pkwy 2E, Mountain View, CA 94043-1351.


Silicon Graphics, SGI, the SGI logo, InfiniteReality, IRIX, Octane, Onyx2, and Origin are registered trademarks, and IRIS InSight, NUMAflex, NUMAlink, SGIconsole, Supportfolio, and XIO are trademarks of Silicon Graphics, Inc.

MIPS is a registered trademark of MIPS Technologies, Inc. used under license by Silicon Graphics, Inc.

Linux is a registered trademark of Linus Torvalds.

Record of Revision

Revision 001August 2001 
Initial Revision

Revision 002April 2002 
This revision includes the following changes:

- Changed the size of the rear mounting bracket from 6 inches to 2 inches.
- Changed the number of required mounting-bracket screws from 4 screws  to 2 screws.
- Indicated that you no longer have to remove the chassis rail from the server when you install or remove a full-height PCI card in PCI slot 2.
- Indicated that you must remove the hinged cover from the server when you  install or remove a customer-replaceable unit.
- Updated the power-on and power-off procedures.
- Updated the instructions that describe how to install a server in an SGI  rack.
- Added connector pinouts.
- Removed the appendix that contained L1 controller information.
- Added references to the SGI L1 and L2 Controller Software User's Guide.

SGI Origin 300 User's Guide
(document number: 007-4365-002 / published: 2002-06-11)    table of contents  |  additional info  |  download

    Front Matter
    About This Guide
    Chapter 1. Overview of the SGI Origin 300 Server
    Chapter 2. Installation Instructions
    Chapter 3. Setting Up and Operating the Server
    Chapter 4. Installing and Removing Customer-replaceable Units
    Appendix A. Technical Specifications
    Appendix B. Connector Pinouts
    Appendix C. Regulatory Specifications

Home    •     What's New    •     Help    •     Terms of Use    •     Privacy Policy    •

© 2009 - 2015 Silicon Graphics International Corp. All Rights Reserved.