SGI Techpubs Library

Hardware  »  Books  »  End-User  »  
 Indigo2 IMPACT Workstation Owner's Guide
(document number: 007-2849-004 / published: 1996-06-29)    table of contents  |  additional info  |  download
find in page

Chapter 4. Installing and Removing Standalone Option Boards
Prev   Next

Chapter 4. Installing and Removing Standalone
Option Boards

This chapter tells you how to install and remove EISA (Extended Industry Standard Architecture) and GIO (Graphics Input/Output) boards. EISA and GIO boards add functionality to your system through a standard bus.

Note: PC software device drivers are not compatible with the Indigo2 IMPACT workstation.

Installing the Texture Memory Option Board

To remove or replace the Indigo2 High IMPACT Texture Memory Option Board, see Chapter 5, “Identifying, Installing, and Removing Graphics Boards and Attached Option Boards.”

Installing EISA and GIO Option Boards

To install an EISA or GIO option board, you must shut down the system, remove the cover, attach the wrist strap, install the option board, replace the cover, and start up the system.

Shutting Down and Powering Off the System

To shut down and power off the system, follow these steps:

  1. Open the front cover.

    Figure 4-1. Opening the Front Cover


  2. Press and release the power switch on the front of the workstation to shut down the software and power off the system.

    Figure 4-2. Powering Off the System


    The system powers off automatically.

  3. Disconnect the power cable from the back of the workstation.

  4. Disconnect the monitor cable from the back of the workstation.

Removing the Cover

To remove the cover, follow these steps:

  1. Remove the bezel.

    • Press down on the tabs on each side of the bezel, as shown in Figure 4-3.

      Figure 4-3. Releasing the Bezel


  2. Remove the lockbar, if one is installed.

    • Remove the lock from the lockbar at the back of the workstation.

    • Slide the lockbar out through the bezel.

    • Pull the bezel down and away from the chassis.

      Figure 4-4. Removing the Bezel


  3. Remove the top cover.

    • Press up on the tabs on each side of the drive openings and pull up on the cover, as shown in Figure 4-5.

      Figure 4-5. Releasing the Top Cover


    • Rotate the cover back and away from the chassis, as shown in Figure 4-6.

      Figure 4-6. Removing the Top Cover


Tip: If the cover is difficult to raise, check the locking levers of your drives to be sure they are fully locked. The levers should be pushed all the way to the right.

Installing an EISA or GIO Option Board

To install an EISA or GIO option board, follow these steps:

  1. Ground yourself to a metal part of the Indigo2 IMPACT chassis.

    Caution: The EISA or GIO board is extremely sensitive to static electricity; you must wear the wrist strap while installing it. The wrist strap prevents the flow of static electricity, which could damage the board.

    • Unwrap the first two folds of the band and wrap the exposed adhesive side firmly around your wrist.

    • Unroll the rest of the band and peel the liner from the copper foil at the opposite end.

    • Attach the copper foil to a convenient and exposed electrical ground, such as a metal part of the Indigo2 IMPACT workstation.

  2. Move the workstation or position yourself so that you are facing the option slots.The option slots are located at the side and rear of the workstation, as shown in Figure 4-7.

    Figure 4-7. Locating the Option Slots


  3. Open the metal panel located in front of the option slots by pulling up on the panel and lowering it.

  4. Remove the retention pin on the right side of the boards, as shown in Figure 4-8.

    Note: Check the placement of the retention pin. It hangs in front of the board, not beside it.

    Figure 4-8. Removing the Retention Pin


  5. Locate the EISA or GIO connector for the board or boards you are installing. Your Indigo2 IMPACT workstation has two sets of option connectors, as shown in Figure 4-9.

    • three EISA connectors, located on the midplane toward the rear of the workstation

    • four GIO connectors, located on midplane, toward the front of the workstation

      Figure 4-9. Locating the EISA and GIO Connectors


Installing Option Boards and the Solid IMPACT Graphics Board Set

Note: For proper placement of your option board in relation to the board set you purchased with your Indigo2 IMPACT workstation, refer to Table 4-1, Table 4-2, Table 4-3, and Figure 4-10.

Table 4-1. Placement of Solid IMPACT Board and Option Boards

If you have this combination of Indigo2
Solid IMPACT board and option boards:

Use these slots:

Solid IMPACT board plus 1 GIO option board

Place Solid IMPACT board in Slot B and GIO board in Slot C

Solid IMPACT board plus 1 GIO and 1 EISA option board

Place Solid IMPACT board in Slot B, GIO board in Slot C, and EISA board in Slot A

Solid IMPACT board plus 1 EISA board

Place Solid IMPACT board in Slot B and

EISA board in Slot A or Slot C

Solid IMPACT board plus 2 EISA boards

Place Solid IMPACT board in Slot B and

EISA boards in Slot A and Slot C

Solid IMPACT board plus 3 EISA boards

Place Solid IMPACT board in Slot D and EISA boards in Slots A, B, and C


Note: Although there are four GIO connectors, only one of each pair of GIO connectors, 0–0 or 1–1, may be used. You may connect only one GIO board or board set to one “0” connector in the pair 0–0, or to one “1” connector in the pair 1–1. See Figure 4-10.

Figure 4-10. Identifying Board Slots


Installing Option Boards and the High IMPACT Graphics Board Set

Install the board set in the same slots as before. If you need help locating the correct slots for your board set, see Table 4-2

Table 4-2. Placement of Indigo2 High IMPACT Board Set and Option Boards

If you have this combination of Indigo2 High IMPACT and option boards:

Use these slots:

Indigo2 High IMPACT (2 board set) plus 1 GIO option board

Place Indigo2 High IMPACT board set in Slots A and B, and GIO option board in Slot C

Indigo2 High IMPACT board set plus
1 EISA option board

Place EISA option board in Slot A, and Indigo2 High IMPACT board set in Slots B and C

Indigo2 High IMPACT board set plus
2 EISA option boards

Place EISA boards in Slots A and B and the Indigo2 High IMPACT board set in Slots C and D

Indigo2 High IMPACT board set plus 1 GIO option board and 1 EISA option board

Place EISA option board in Slot A, Indigo2 High IMPACT board set in Slots B and C, and GIO option board in Slot D


Installing Option Boards and the Maximum IMPACT Graphics Board Set

Install the board set in the same slots as before. If you need help locating the correct slots for your board set, see Table 4-3

Table 4-3. Placement of Maximum IMPACT Board Set and Option Boards

If you have this combination of Indigo2 Maximum Board Set and option boards:

Use these slots:

Maximum IMPACT Board set plus 1 GIO option board

Place Maximum IMPACT board set in Slots A, B, and C and GIO option board in Slot D

Maximum IMPACT board set plus
1 EISA option board

 

Place EISA option board in Slot A and Maximum IMPACT board set in
Slots B, C, and D

Look at the left end of your board and find the port. Determine where the port will exit the chassis when the board or board set is inserted into the option slot.

Figure 4-11. Placement of Option Board


  1. Remove the corresponding I/O panel over the slot. This makes the port accessible.

    • Remove the screw that attaches the I/O panel to the chassis. The screw opening is located on the metal bracket on the upper left side of the board.

    • Save the screw to secure the option board after it is installed.

      Figure 4-12. Removing the I/O Panel


    If your site has multiple Indigo2 IMPACT workstations, it's a good idea to save at least one set of I/O panels to reinstall in the workstation should you need to remove an option board.

  2. Install the board.

    • Align the right side of the board with the metal grooves on the right.

    • Align the Input/Output port with the port opening that allows access to the exterior of the chassis. Push the board into the slot until the connector on the back of the board is securely connected to the connector on the midplane, as shown in Figure 4-13.

  3. Insert and tighten the screw that holds the board to the chassis.

    The screw opening is located on the metal bracket on the upper left side of the board. See Figure 4-13.

    Figure 4-13. Installing the Option Board


  4. Hang the retention pin so that it sits in front of the board set. The retention pin prevents the board set from moving away from the connectors. See Figure 4-14.

    Figure 4-14. Replacing the Retention Pin


    Tip: Use the retention pin as a plumb line to determine if the board set is properly seated. If the pin is tilted, push on the board set until it is properly connected.

  5. Tip the metal panel up until it snaps into place, as shown in Figure 4-15.

    Figure 4-15. Closing the Metal Panel in Front of the Option Slots


Replacing the Cover

To replace the cover, follow these steps:

  1. Locate the tabs on the inside and back of the top cover and the slots on the back of the workstation. See Figure 4-16.

  2. Face the front of the workstation.

    • Look through the slots as you lower the cover and move the tabs into place.

    • Slide the tabs into the slots and pull the cover down until it snaps into place. The cover fits tightly over the workstation.

      Figure 4-16. Replacing the Top Cover


  3. Replace the bezel.

    • Place the tabs on the bottom of the bezel in the grooves in the front of the chassis, as shown in Figure 4-17.

  4. Tilt the bezel up until it snaps into place.

  5. Reinstall the lockbar, if you removed it.

    • Slide it through the bezel and out the back of the workstation.

    • Reattach the lock.

    • Close the front panel of the bezel.

      Figure 4-17. Replacing the Bezel


Reconnect the power cable and monitor cable to the connector on the back of the workstation.

You are finished installing the option board and are ready to turn on the workstation.

Turning On the Workstation

To turn on the workstation, follow these steps:

  1. Turn on the monitor.

    The monitor's power switch is on the front of the monitor in the lower right corner. The LED next to the switch lights up when you turn on the monitor.

  2. Turn on the system power.

    • Open the front cover by snapping it away from the top edge of the chassis and tipping it down.

    • Press the power switch to turn on the system, as shown in Figure 4-18.

      Figure 4-18. Turning On the Indigo2 IMPACT Workstation


Removing EISA and GIO Option Boards

To remove a GIO or EISA option board, follow these steps:

  1. For instructions on how to shut down and power off the system, see “Shutting Down and Powering Off the System”.

  2. For instructions on how to remove the cover, see “Removing the Cover”.

  3. Ground yourself to a metal part of the Indigo2 IMPACT workstation.

    • Unwrap the first two folds of the band and wrap the exposed adhesive side firmly around your wrist.

    • Unroll the rest of the band and peel the liner from the copper foil at the opposite end.

    • Attach the copper foil to a convenient and exposed electrical ground, such as a metal part of the Indigo2 IMPACT workstation.

    Caution: The EISA or GIO board is extremely sensitive to static electricity; you must wear the wrist strap while installing it. The wrist strap prevents the flow of static electricity, which could damage the board.

  4. Move the workstation or position yourself so that you are facing the option slots.The option slots are located on the side toward the rear of the workstation. See Figure 4-19.

  5. Open the metal panel located in front of the option slots by pulling up on the panel and lowering it down, as shown in Figure 4-19.

    Figure 4-19. Opening the Metal Panel in Front of the Option Slots


    Note: Look at the placement of the retention pin before you remove it. It hangs between the edge of the board set and the metal panel you just opened.

  6. Remove the retention pin, as shown in Figure 4-20.

    Figure 4-20. Removing the Retention Pin


  7. Remove the screw attaching the option board to the workstation slot, as shown in Figure 4-21. The screw is located on the metal bracket on the upper left side of the board.

    Figure 4-21. Unscrewing the Option Board From the Indigo2 IMPACT Chassis


  8. Pull the board out of the workstation.

    • Grasp the board with both hands, and pull it out of the slot.

    • Set the board down on a flat, antistatic surface so that the side with the chips on it faces up.

  9. If you are replacing the board, see “Installing an EISA or GIO Option Board”.

  10. If you are not immediately replacing the board, install the metal I/O panel. You need a Phillips screwdriver to do so.

    Caution: The I/O panel is required to keep your graphics boards at the appropriate temperature and to prevent interference with other electrical equipment.

    • Slide the metal I/O panel into the slot on the left side of the option slots.

    • Place the screw into the opening on the chassis, and tighten the metal I/O panel to the chassis using the Phillips screwdriver.

      Figure 4-22. Replacing the Metal Port Cover


  11. Hang the retention pin so that it sits in front of the board set. The retention pin prevents the board set from moving away from the connectors. See Figure 4-23.

    Figure 4-23. Replacing the Retention Pin


  12. Replace the cover. For instructions, see “Replacing the Cover”.

You are finished removing the option board.

To turn on the workstation, see “Turning On the Workstation”.

Prev Table of Contents Next
Chapter 3. Installing and Removing Memory  Chapter 5. Identifying, Installing, and Removing Graphics Boards and Attached Option Boards  

Indigo2 IMPACT Workstation Owner's Guide
(document number: 007-2849-004 / published: 1996-06-29)    table of contents  |  additional info  |  download

    Front Matter
    Chapter 1. Introduction
    Chapter 2. Getting Started
    Chapter 3. Installing and Removing Memory
    Chapter 4. Installing and Removing Standalone Option Boards
    Chapter 5. Identifying, Installing, and Removing Graphics Boards and Attached Option Boards
    Chapter 6. Installing and Removing Peripherals: Internal and External Devices
    Chapter 7. Installing and Removing Software
    Chapter 8. Troubleshooting
    Chapter 9. Ordering, Removing, and Installing Replacement Parts
    Chapter 10. Maintenance, Safety, and Regulatory Information
    Appendix A. Cable Pinout Assignments
    Appendix B. International Keyboard Support
    Appendix C. Exterior and Interior of Workstation
    Glossary
    Index


home/search | what's new | help